Rhino

  • This product contains the M6 x 16mm Dowel Nut in a pack of 10 and can be used either as a spare part or replacement.

     

    $3.00
  • This product contains the M6 x 35mm Torx27 Pan Head Screw (Stainless Steel) in a pack of 4 and can be used either as a spare part or replacement.

     

    $3.00
  • Rhino Vortex Bar Rubbber 400mm

    The M626 VGS Vortex Bar Rubber is a 400mm strip sold individually and designed to reduce wind noise as well as giving your roof racks additional padding and styling

    Features:

    • Available in lengths of 400mm
    • Easy to install/remove
    • Reduces wind noise
    • Provides additional padding and styling
    • Short pieces facilitate accessory fitting
    • Sold individually
    $4.00
  • Do you need end caps for your Rhino Heavy Duty Roof Racks? Maybe you've lost one or two of them. Available is the M002 end cap to suit your Rhino Heavy Duty crossbar. Sold as individual units, these end caps will fit in seamlessly.

    Features:

    • Direct replacement end cap for your Rhino Heavy Duty bars
    • Sold as an individual end cap
    • Simple to fit
    $5.00
  • Need a bit of extra height on your Heavy Duty CXB roof rack bars? This pair of spacers will give you an extra 6mm of height to work with.

    Set up is straight forward – simply insert each spacer between the leg and bar using the provided hardware and you’re all done.

    Features:

    • Adds an extra 6mm of height to your bars
    • Specifically designed for use with Rhino-Rack Heavy Duty CXB Roof Rack Systems
    • Includes 2 leg spacers
    $10.00
  • The VA-FK2 is a fitting kit designed to fit the Vortex bar to RLCP legs

    $10.00
  • The VA-FK1 is a fitting kit designed to fit the Vortex bar to RL legs

    $11.00
  • The RLKS1 spacer blocks are used to level a 3 bar roof rack system on a vehicle such as a ute or pick up that may have rear ute posts or a canopy rack system. Attached between the Rhino-Rack 2500 leg and either a Rhino-Rack Heavy Duty or Vortex cross bar, this set of spacers will raise the cross bar 10mm in height.

    These leg height spacers have been designed for use on a support bar, set up for long loads - they are not to be used as a 2 bar system under a load bearing cross bar. Made from glass re-enforced nylon, just like our legs, they are strong and flexible.

    This kit includes:

    • 2 x 10mm Spacer Blocks
    • 2 x M6 x 32mm Bolts
    $14.00
  • Rhino Swivel Pad for 2500 systems.

    Includes one swivel pad.

     

    $14.00
  • The 5mm Quick Mount Base Wedge is designed to create a level bar when fitting an RLT600 Quick Mount leg to a track position that is curved or angled.

    It is very important to create a level leg position especially when fitting Pioneer systems onto the RLT600 legs. This will ensure the Quick Mount legs to easily click in and out.

    Sold as a pair.

     

    $16.00
  • This front/rear wedge kit is designed to have the legs level to enable a Pioneer system to mount straight on.

     

    $16.00
  • The Foxwing Pole Service Kit consists of a replacement hinge which has been engineered to withstand most conditions the Foxwing Awning might be exposed to. Made from an engineered plastic which replaces the cast alloy design of the regular hinge, this product is quick and easy to replace.

     

    $17.00
  • Rhino Quick Mount 10mm VA spacer

    The Quick Mount Vortex Spacer (10mm) allows you to fit the Rhino-Rack Vortex Bars to the RLT600 legs. Sold as a pair of 2 which fits 1 bar.

     

     
    $17.00
  • VORTEX LEG HEIGHT SPACERS

    Spacer blocks are useful to obtain a level height between all of the crossbars on your vehicle. Installation is a breeze - simply place the spacers between the leg unit and the crossbar of your roof rack until all of the crossbars have been raised to an even level.

    $18.00