Yakima

  • From $10.00
  • End Cap for Forklift, Frontloader Bike Carriers

    From $10.00
  • From $14.00
  • Features:

    • Creates up to two mounting points for Bow/Stern Tie-Downs on vehicles without easy access mounting points

    • Two nylon looped straps that can be mounted directly to the vehicle inside the hood

    $20.00



  • From $30.00
  • These strong straps, with quick and easy-to-use buckles, ensure that if you hear the words 'boat' and 'projectile' in the same sentence, it won't be in reference to you.

     

    FEATURES:

    • Soft rubber buckle cover protects boat and vehicle from scratches

    • Straps can be cut to length if required

    • Box-stitched polypropylene webbing is super strong

    • Sold in pairs of 4.9 m (16-foot) straps

    • Looking for a locking feature to your cargo tie-down solution?  Check out the Yakima RipCords - they're lockable and include our SKS lock cores

    SPECIFICATIONS:

    Heavy duty nylon straps with padded buckles to protect your vehicle and boat from scratches.

     

    FAQS:

     Q. Won’t the buckle scratch the paint on my car?
    A. Not with the super sweet padded Ancra buckle.

    Q.  What will it hold down?
    A.  What WON’T it hold down?  This thing will keep your gear glued to your rack.

    $59.00
  • Give your truck bed a permanent bike mounting solution with this fork style mount. In fact, this mount, with single-sided adjustment skewer for easy loading, can be installed anywhere you can put a couple bolts. Go ahead, get creative.

     

    FEATURES AND BENEFITS

    • A “bolt anywhere” fork style bike mount
    • Single-sided adjustment skewer with long throw for easy bike loading
    • Corrosion-resistant anodised aluminium construction

     

    SPECIFICATIONS:

    WEIGHT: < 0.5 kg (1 lb)

    DIMENSIONS:
    Bracket Length: 10.2 cm (4”)
    Bracket Height: 5.1 cm (2”)

    CAPACITY: 1 Bike

     

     

    FAQ

    Q: Does it carry all bikes?
    A: The BlockHead carries just about any bike with a quick release wheel skewer.  However, there are a few exceptions where one of our other mounts should be used instead. These exceptions include, but are not limited to, bikes with nutted front wheels, triple clamp forks, forks with dropout spacing (the distance between the forks at the tips) other than 100 mm, and some bikes with front disc brakes.

    Q: What is it made of?
    A: The main pedistal is heat-treated and anodized aluminum, the quick-release skewer is primarily stainless steel.

    $59.00
  • Give your truck bed a permanent bike mounting solution with this fork style mount. In fact, this mount, with single-sided adjustment skewer for easy loading, can be installed anywhere you can put a couple bolts. Go ahead, get creative.

     

    FEATURES AND BENEFITS

    • A “bolt anywhere” fork style bike mount
    • Single-sided adjustment skewer with long throw for easy bike loading
    • Includes locking skewer with SKS LOCK CORE
    • Corrosion-resistant anodised aluminium construction

     

    SPECIFICATIONS:

    WEIGHT: < 0.5 kg (1 lb)

    DIMENSIONS:
    Bracket Length: 10.2 cm (4”)
    Bracket Height: 5.1 cm (2”)

    CAPACITY: 1 Bike

     

     

    FAQS:

     

    Q: What tools do I need?
    A: This application requires drilling holes into your truck; a drill and drill bits will be really handy and a tool to tighten down the bolts or screws and nuts.

    Q: Does it carry all bikes?
    A: The Locking BlockHead carries just about any bike with a quick release wheel skewer. However, there are a few exceptions where one of our other mounts should be used instead. These exceptions include, but are not limited to, bikes with nutted front wheels, triple clamp forks, forks with dropout spacing (the distance between the forks at the tips) other than 100 mm, and some bikes with front disc brakes.

    Q: What is it made of?
    A: The main pedestal is heat-treated and anodized aluminum; the quick-release skewer is primarily stainless steel.

    $99.00
  • Don't just throw your bike in the bed of your truck. Mount it. With the BedHead you can fork mount your bike to the inside lip of your truck bed without any drilling. Easy to load, easy on your paint job and hardly takes up any room in your truck bed.

     

    FEATURES AND BENEFITS

    • Ute bed bike fork mount that allows you to attach your bike to the inside lip of your Ute bed rail without any drilling
    • Single-sided adjustment skewer with long throw for easy bike loading
    • Corrosion-resistant anodised aluminium construction
    • Soft padding to protect your vehicle’s paint job

     

    SPECIFICATIONS:

    WEIGHT: 1 kg (2.2 lbs)

    DIMENSIONS:
    Length: 10.2 cm (4")
    Width: 4.5 cm (1-¾")
    Height: 7.6 cm (3")

    CAPACITY: 1 bike

     

    FAQS: 

    Q: Does it lock?
    A: No, but the Locking BedHead does.

    Q: Do I need any tools/drills to apply this?
    A: No tools or drilling required.

    Q: Does it carry all bikes?
    A: The BedHead carries just about any bike with a quick release wheel skewer. However, there are a few exceptions where one of our other mounts should be used instead. These exceptions include, but are not limited to, bikes with nutted front wheels, triple clamp forks, forks with dropout spacing (the distance between the forks at the tips) other than 100mm, and some bikes with front disc brakes.

    $99.00
  • This 15mm x 110 thru-axle adapter allows modern mountain bikers to quickly secure their bike on any traditional 9mm fork style bike mount.

    FEATURES:

    • 15mm x 110mm

    • Axle is not included

    • Built in safety tabs

    • Durable black powder coat finish

    $99.00
  • Keep your shovel or any other longitudinal gear at easy reach. And free up more space in your vehicle.

    Features:

    • Unique "pop & drop" mechanism - simply pop open the handcuff-sinpired holders and drop your tool in.

    • Securely holds handle diameters between 30-55mm and can also be locked for extra peace of mind.

    • Ideal for tools with straight shafts (shovels), "D" handle (spades), and oval handles (axes), as well as sporting equipment (paddles or oars).

    $99.00
  • Mako Aero

    These practical saddle-style rooftop kayak mounts come with all the hardware you need to secure your boat with a kung-fu grip, yet cradle it gently and keep it looking pretty. Mako Aero saddles fit car rack systems with factory crossbars out of the box, and offer SKS security. Mako Aero rooftop kayak mounts are sold in sets of two, so you can pair them with another set to carry one kayak. Or for super ease of loading, you can pair them with boat load assist HullyRollers.

    FEATURES:
    - Mako pads protect the hull, and Dynaflex™ grips provide a snug hold when you tighten the straps
    - Sold in a set of two saddles, you will need two sets for one vehicle or pair a set of Make Aero Saddles with a set of our HullyRollers to make for easy loading.
    - Padded buckle protects your boat and your vehicle
    - MakoAero saddles fit car rack systems with round, square and factory crossbars out of the box
    - SKS locking system (LOCK CORES sold separately)


    SPECIFICATIONS:
    - Saddle-type carrier that cradles a kayak hull-side down on rack. Universal mounting hardware included.
    - Fit List on carton
    - For use with plastic and composite hulls.
    - Included Mako Pads add an extra layer of protection at contact points with boat to protect hull's finish (suggested for optimal protection of gel-coated composite hulls). The pads also allow for easier sliding of kayak into cradles.
    - SKS compatibility.
    - Use our HeavyDuty strap instead of the two piece strap previously used in the Mako.

    GENERAL INFORMATION:
    DIMENSIONS: 21.6 cm (8.5") H x 19.7 cm (7.75") W x 24.1 cm (9.5") L
    WEIGHT: 1.8 kg (4 lbs)

    $129.00
  • A smart fairing that easily attaches to any Yakima bar – and just about any other brand's bars– to quiet wind noise and reduce drag.

    Features:

    • Moves airflow up and over the rack to reduce drag and quiet wind noise
    • Universal mounting attachment works with any Yakima bar – StreamLine or RoundBar
    • Also fits square bars and most factory bars
    • Band-style attachment quickly and easily attaches to any crossbar
    • Secures with easy-to-reach adjustments and included tool
    • Available in 4 sizes

    Sizes:

    • 34"
    • 40"
    • 46"
    • 52"
    From $139.00
  • The unique ForkChop is a highly versatile fork mount bike carrier. It transports virtually any bike, including both quick release and thru-axles, and does it all without touching the bike frame. The ForkChop even fits 15mm thru-axle fat bikes out of the box or 9mm x 135mm with the optional Fat Bike QR Locking Skewer accessory. The split design makes it ideal for use with a cargo basket or for a minimalist look on your vehicle's roof rack.

    FEATURES:

    • Securely carries a variety of bike styles with no frame contact

    • Interchangeable inserts work with most axle configurations including quick release (9 mm) and thru-axles (12 x 100 mm, 15 x 100 mm, 15 x 110 mm, 15 x 135/142/150mm)

    • Split design gives a minimalist appearance and creates increased functionality when used with cargo baskets

    • Tool-free, universal mounting hardware fits most roof racks

    • Fully assembled out-of-the box

    • Optional Fat Bike QR Locking Skewer makes the rack compatible with 9mm x 135 mm fat bikes (sold separately)

    • Add SKS locks (2) to secure your bike to the rack and the rack to the vehicle (sold separately)

    Fitting:

    • Crossbar spread must be ±25cm (±10”) of your bike wheelbase for proper use.

    • Crossbars must be a minimum 81cm (32”) apart.

    • For some vehicles with fixed point roof rack mounting, the minimum spread is wider than the fixed points, which cannot be adjusted.

    • Maximum spread of 127cm (50”) apart.

    • Reverse the rear wheel tray for a shorter crossbar spread.

    • Reverse the head unit if there is interference between your fork and/or brake calipers.

    GENERAL INFORMATION:

    WEIGHT: 1.6 kg (3.5 lbs)
    DIMENSIONS: 178mm (7") L x 127mm (5") W x 89mm (3.5") H
    CAPACITY: 1 bike up to 18 kg 

    $159.00
    $159.00
  • The GateKeeper tailgate pad is a perfect companion for ute bed bike transport. The durable nylon exterior protects your bike from your ute’s tailgate while the soft felt backing keeps your ute’s paint protected. Integrated SitTight™ bike cradles add extra stability and protection for your bikes and the HindSight™ tuck-away cover opens up the view for your reverse camera, leaving you with a worry free shuttle to the top.

     

    Features

     

    • Tailgate pad for your ute that securely carries your bikes to the trailhead
    • NEW Velcro® cradle closure system is easy on carbon bike frames and painted surfaces
    • Rugged nylon outer material resists abrasion and weather damage
    • Extra soft felt backing protects your ute’s paint job
    • Integrated strap management system keeps the pad tight and secure on the way up the mountain
    • Has a 5 bike capacity and fits most full-size utes
     
    Specification
    Weight
    3.18 kg
    Dimensions
    L 134.6 cm  x  W 43.2 cm  x  H 12.7 cm
    Capacity
    5 bike capacity
    $219.00
  • Yakima forklift bike carrier

    Feast your eyes on our first-ever fork-style roof rack bike mount with factory crossbar capability right out of the box. (Please note: The ForkLift is recommended for carrying bikes only, not pallets loaded with heavy gear.)

    Specifications

    • Fork to factory bar mount, bike rack. Accommodates disc brakes and standard axles. Long-throw skewer with integrated adjuster knob.
    • Quick and easy, tool-free installation makes life a breeze 
    • Sleek design and automotive finish looks extremely spiffy on your vehicle 
    • Secure and lockable skewer with integrated adjustment knob for single-handed, easy access (SKS lock cores sold separately) 
    • Easy-to-adjust sliding wheel tray makes positioning the rear wheel a snap
    • Fits round, square and most factory crossbars out of the box.

    Features:

    • Simple tool-free installation and removal of the bike mount from your car roof rack 
    • Fits most disc brakes 
    • Secure and lockable skewer with integrated adjustment knob for single-handed, easy access (SKS LOCK CORES sold separately) 
    • Easy-to-adjust sliding wheel tray makes positioning the rear wheel a snap 
    • Fits car rack systems with round, square and most factory crossbars right out of the box 
    • Doesn’t touch the painted surfaces of your bike and makes for a great bike mount for your carbon rig

    General Information:

    • Weight: 7 lbs.
    • Dimensions: 53.5” long
    • Capacity: 1 bike

     

     

     

     

    $249.00
    $199.00